年表作成・共有サービス - pastport

https://www.titansuhelift.com/product/steel-wire-rope/

Steel Wire Rope
Steel Wire Rope is one of the most support steel wire rope sling parts of industrial machinery, construction, fishery and forestry. It is designed for dynamic movement such as lifting of crane hoists, conveying of elevators and control cables of automobile, motorcycle, gate and so on. It is also used statically as stay wire in building and bridge constructions.

TITANSUHE has been in rope steel wire field more than 15 years. Our wire ropes are designed to meet the quality and specifications of almost all national and international standard. From hoist ropes, compensation ropes, governor ropes and control ropes, you can find all of them from us.

Categories of TITANSUHE's steel wire ropes

Elevator wire ropes
6x19S+FC,6x19W+FC,6x25F+FC,6x29F+FC,6x36WS+FC,8x19S+FC,8x19W+FC,8x25F+FC,8x19S+IWRC,8x19W+IWRC,8x25F+IWRC,8x19S+IWRF,8x19W+IWRF,8x25F+IWRF,8x19S+IWRF

General Engineering Wire Ropes
6x19+FC, 6x19+IWS or IWR, 6x37+FC, 6x37+IWR or IWS, 6x61+FC, 6x61+IWR, 8x61+FC, 8x61+IWR, 18x7+FC, 18x7+IWS, 34x7+FC, 35x7

Fish Wire Ropes
6x12+7FC, 6x24+7FC

Aircraft Cables
7x7,7x19

Stainless Steel Wire Ropes
6x7+FC, 7x7, 7x19, 6x19+FC, 6x36+IWRC

What is Tensile Grade of Steel Wire Ropes?

The tensile grade of a wire rope refers to the strength of its constituent wires. For general engineering wire ropes, there is only single tensile grade, normally comes as 1570n/mm2, 1670n/mm2, 1770n/mm2, 1870n/mm2, 1960n/mm2 and 2160n/mm2. For elevator wire ropes, they have dual tensile strength and outer wires is lower tensile strength, inner wires is higher tensile strength, for example 1180/1770n/mm2 or 1370/1770n/mm2.

What Kind of Wire Ropes are Used for Elevator?

The most used wire ropes for elevator are 6 strands or 8 strands wire rope constructed with Seale strand, Warrington Strand or Filler Wire Strand.

Seale strand has larger diameter of wires on the outer layer and has smaller wires on the inner layer. The larger wires has better abrasion resistance, while the smaller wires offer better flexibility.

Warrington has an alternative arrangement of smaller and larger wires on the outer layer to get a combination of flexibility and abrasive properties.

Filler Wire has smaller wires filling the empty spaces between outer and inner layer. This kind of strand provides better fatigue resistance and good abrasive properties.

Tips of Safe Use Steel Wire Ropes

Care must be taken during rope installation since the rope is not supported when it is unrolled from the reel, until it is properly installed.

Care must be taken to unroll and not laterally pull wire rope when pulling it off the reel. Be careful not to get any loops.

Wire rope cutting: Both sides of cutting point apart 10-20mm using iron wire to tie up, the tie length is 2-4 times of rope diameter. Use proper tools to cut wire ropes. If such tools are not available and a cutting torch must be used, prevent short circuit occurring between the torch tip and the wire rope. When welding job is performed in the elevator shaft, prevent any debris getting on the wire rope and causes damage.

If the wire rope is not straight right off the reel, apply tension to the rope and fix it to proper form.

Do not drag ropes over sharp edges, and prevent any dirt and debris sticking on the rope. This will cause damage to the traction groove and rope itself.

Ropes must be prevented from rotating during installation since free-hanging ropes will untwist under their own weight.

Check the rope tension after mounting with a suitable device. Make sure all ropes in the same group are evenly tensioned.

As one of lifting equipment manufacturers, we can offer kinds of lifting products for sale, if you have needs, please contact us.