Screw and Barrel for Rubber Extrusion

(2022年05月12日)

Detail Information For Rubber Screw and Barrel:

Application: for different kinds of rubber.

Customer's Requirement: extrude rubber continuously, stably and uniformly.

Screw's quality: bimetallic quality or nitriding quality.

Barrel's quality: bimetallic quality or nitriding quality.

Detail Information For All Rubber Screw and Barrel:

Brief introduction:  
cold& hot feeding screw and barrel, such as pin type, conical type, venting type, injection type and etc, has good torque force& abrasion resistance, rubber will be extruded out uniformly and stably.

Specification:
1:For cold feeding screw and barrel
Diameter range: Ф40-Ф300MM
L/D ratio: 8-20

2: For hot feeding screw and barrel
Diameter range: Ф30-Ф250MM
L/D ratio: 4-8

3: for Pin type screw and barrel:
Diameter range: Ф60-Ф250MM
L/D ratio: 12-18

Base material :
38CrMoAlA(JIS SACM645) from BAOSTEEL company.
Alloy Layer: Fe, Wc, Si, Cr, Ni, Co, C, Mo, B and etc ( different quality has different formula).

Quality grade for screw and barrel:
Nitriding quality--------common quality type.
Bimetallic quality-------better abrasive& corrosive resistance, has different quality grade.

Heat treatment:
Advance hardening and tempering
Nitriding treatment

Technical Parameters:
Nitriding depth: 0.50mm-0.80mm                                
Nitriding hardness: HRC56-58                          
Surface roughness: Ra 0.4                  
Screw straightness: 0.015mm  
Alloy layer depth: 2mm-3mm
Alloy layer hardness: HRC56-64

OULIN SCREW:  YOUR LOYAL PARTNER FOR SCREW AND BARREL

Detail Information For Rubber Screw and Barrel:

Application: for different kinds of rubber.

Customer's Requirement: extrude rubber continuously, stably and uniformly.

Screw's quality: bimetallic quality or nitriding quality.

Barrel's quality: bimetallic quality or nitriding quality.

Detail Information For All Rubber Screw and Barrel:

Brief introduction:  
cold& hot feeding screw and barrel, such as pin type, conical type, venting type, injection type and etc, has good torque force& abrasion resistance, rubber will be extruded out uniformly and stably.

Specification:
1:For cold feeding screw and barrel
Diameter range: Ф40-Ф300MM
L/D ratio: 8-20

2: For hot feeding screw and barrel
Diameter range: Ф30-Ф250MM
L/D ratio: 4-8

3: for Pin type screw and barrel:
Diameter range: Ф60-Ф250MM
L/D ratio: 12-18

Base material : 
38CrMoAlA(JIS SACM645) from BAOSTEEL company.
Alloy Layer: Fe, Wc, Si, Cr, Ni, Co, C, Mo, B and etc ( different quality has different formula).

Quality grade for screw and barrel:
Nitriding quality--------common quality type.
Bimetallic quality-------better abrasive& corrosive resistance, has different quality grade.

Heat treatment:
Advance hardening and tempering
Nitriding treatment

Technical Parameters:
Nitriding depth: 0.50mm-0.80mm                                
Nitriding hardness: HRC56-58                          
Surface roughness: Ra 0.4                  
Screw straightness: 0.015mm  
Alloy layer depth: 2mm-3mm
Alloy layer hardness: HRC56-64 

OULIN SCREW:  YOUR LOYAL PARTNER FOR SCREW AND BARREL

  https://www.oulinscrewbarrel.com/nitriding-screw-and-barrel-for-rubber/

コメント